995 Wheel Loader

995 Wheel Loader

360° Exterior View

Built to the same size as the 994K but offering a higher rated payload, the new Cat® 995 Wheel Loader gives you greater productivity and performance while using less fuel. ...
PDF Print Share

Engine

Engine Model
Cat® 3516E
Emissions
U.S. EPA Tier 4 Final/EU Stage V or U.S. EPA Tier 1 equivalent
Engine Power - ISO 14396
1847hp
Gross Power - SAE J1995
1870hp
Net Power - SAE J1349 - Standard Ambient
1739hp
Net Power - SAE J1349 - High Ambient
1696hp
Bore
6.7in
Stroke
8.5in
Displacement
4766in³
Peak Torque - 1,200 rpm - SAE J1995
8549lb/ft
Torque Rise
39%
Note (1)
The power ratings apply when tested under the reference conditions for the specified standard.
Note (2)
The net power advertised is the power available at the flywheel when the engine is equipped with fan, alternator, air cleaner and muffler.
Note (3)
The gross power advertised is with the fan at maximum speed.

Operating Specifications

Operating Weight - Standard
543772lb
Bucket Capacity Range
17.2-43.6 m3 (22.3-57 yd3)
Operating Weight - High Lift
547675lb
Rated Payload - Standard Lift (Low to Moderate Digging Resistance)
60ton (US)
Rated Payload - Standard Lift (Moderate to High Digging Resistance)
50ton (US)
Rated Payload - High Lift (Low to Moderate Digging Resistance)
55ton (US)
Rated Payload - High Lift (Moderate to High Digging Resistance)
50ton (US)
Note
*Please contact your local dealer to determine if your application is suitable for this increased rated payload.
Cat Truck Match - Standard
785/789
Cat Truck Match - High Lift
789/793/794

Transmission

Transmission Type
Cat Planetary Power Shift
Forward - 1
4.6mile/h
Forward - 2
8mile/h
Forward - 3
13.6mile/h
Reverse - 1
5mile/h
Reverse - 2
8.8mile/h
Reverse - 3
14.9mile/h
Direct Drive - Forward 1
Lock-up disables
Direct Drive - Forward 2
8.7mile/h
Direct Drive - Forward 3
15.2mile/h
Direct Drive - Reverse 1
Lock-up disables
Direct Drive - Reverse 2
9.6mile/h
Direct Drive - Reverse 3
16.8mile/h
Note
Travel speeds based on 58/85-57 tires.

Hydraulic System - Lift/Tilt

Lift/Tilt System - Circuit
Positive Flow Control
Lift/Tilt System - Pump
Variable Displacement Piston
Maximum Flow at 1,700 rpm Engine Speed
541gal/min
Relief Valve Setting - Lift/Tilt
5004psi
Cylinders, Double Acting - Lift, Bore and Stroke
370 × 1713 mm (14.6 × 67.4 in)
Cylinders, Double Acting - Tilt, Bore and Stroke
310 × 1086 mm (12.2 × 42.8 in)
Pilot System
Open Loop and Pressure Reducing

Hydraulic Cycle Times

Rack Back
4.9s
Raise
12.6s
Dump
3.1s
Lower Float Down
4.2s

Complete System Fill

Fuel Tank - Standard
856gal (US)
Fuel Tank - With 24 hr Attachment
1414gal (US)
Cooling System
138gal (US)
Engine Crankcase
76gal (US)
Transmission
110gal (US)
Differential - Final Drives - Front
220gal (US)
Differential - Final Drives - Rear
200gal (US)
Hydraulic Tank - Implement and Hydraulic Fan
270gal (US)
Hydraulic Tank - Steering and Braking
100gal (US)
Oil Renewal System (ORS)*
20gal (US)
Note
*Not available on Tier 4 Final/Stage V machines. Not available in all regions.

Axles

Front
Fixed
Rear
Trunnion
Oscillation Angle

Cooling System

Ambient Capability Hydraulically Driven Demand Fan - Standard
109.4°F
Ambient Capability Hydraulically Driven Demand Fan - High (Tier 1 equivalent)
131°F
Ambient Capability Hydraulically Driven Demand Fan - High (Tier 4 Final)
127.4°F

Sound Performance - Standard

Operator Sound Level (ISO 6396:2008) - Tier 1/EU Stage I Equivalent
74dB(A)
Machine Sound Level (ISO 6395:2008)
119dB(A)
Note
The declared sound levels listed above include the addition of both measurement uncertainty and uncertainty due to production variation. Typical measurement uncertainty for this type of machine is 2 dBA in accordance with "ISO 4871". The measurement was c

Sound Performance - Suppression

Operator Sound Level (ISO 6396:2008) - Tier 1/EU Stage I Equivalent
73dB(A)
Machine Sound Level (ISO 6395:2008)
117dB(A)
Note
The declared sound levels listed above include the addition of both measurement uncertainty and uncertainty due to production variation. Typical measurement uncertainty for this type of machine is 2 dBA in accordance with "ISO 4871". The measurement was c

Hydraulic System - Steering

Steering System - Circuit
Pilot, Load Sensing
Steering System - Pump
Piston, Variable Displacement
Total Steering Angle
80 degrees
Steering Cycle Times - Low Idle
7.6s
Steering Cycle Times - High Idle
4.3s

Dimensions - Standard Lift - Approximate

B-Pin Height - Maximum Lift
28.8ft
Clearance at Maximum Lift
19.8ft
Dump Angle at Maximum Lift
–50.0 degrees
Front Axle Centerline to Bucket Tip
21.9ft
Ground to Bumper Clearance
4.4ft
Ground to Center of Axles
6ft
Ground to Lower Hitch Clearance
2.9ft
Ground to Top of Exhaust Stacks
23.2ft
Ground to Top of Hood
18.6ft
Ground to Top of ROPS
23.4ft
Maximum Overall Height - Bucket Raised
39.3ft
Maximum Overall Length
64.6ft
Note
Assumes loaded 58/85-57 tires, tires at a static loaded radius of 1830 mm (6 ft), 596-5330 26 m3 (34 yd3) bucket, 431-0064 HD tips.
Rack Angle at Maximum Lift
59.5 degrees
Rack Back Angle - Carry
47.7 degrees
Rack Back Angle - Ground Level
39.7 degrees
Reach - Maximum Lift
9.6ft
Rear Axle - Centerline to Bumper
20.4ft
Tread Width
14.1ft
Wheel Base
22.3ft
Width - Over Tires - With Bulge
18.8ft

Dimensions - High Lift - Approximate

B-Pin Height - Maximum Lift
31.6ft
Clearance at Maximum Lift
22.6ft
Dump Angle at Maximum Lift
–50.0 degrees
Front Axle Centerline to Bucket Tip
24.2ft
Ground to Bumper Clearance
4.4ft
Ground to Center of Axles
6ft
Ground to Lower Hitch Clearance
2.9ft
Ground to Top of Exhaust Stacks
23.2ft
Ground to Top of Hood
18.6ft
Ground to Top of ROPS
23.4ft
Maximum Overall Height - Bucket Raised
42.1ft
Maximum Overall Length
66.9ft
Note
Assumes loaded 58/85-57 tires, tires at a static loaded radius of 1830 mm (6 ft), 596-5330 26 m3 (34 yd3) bucket, 431-0064 HD tips.
Rack Angle at Maximum Lift
59.4 degrees
Rack Back Angle - Carry
53.5 degrees
Rack Back Angle - Ground Level
45 degrees
Reach - Maximum Lift
9.4ft
Rear Axle - Centerline to Bumper
20.4ft
Tread Width
14.1ft
Wheel Base
22.3ft
Width - Over Tires - With Bulge
18.8ft

Brakes

Brakes
ISO 3450:2011

SAFETY

  • Designed for visibility, with a taller windshield that provides a 25% increase in glass surface area for a better view to the bucket, standard rear-view camera, optional Detect 270-degree cameras, standard LED lighting and six-mirror system.
  • Improved access and egress, with integrated powered access system that can be raised and lowered from cab or ground, 45-degree-angle wide stairs, emergency egress ladder, and full handrails on each side.
  • Wide walkways with non-skid surfaces, windshield cleaning platform, and integrated lockout/tagout points designed into the service areas.

OPERATOR COMFORT

  • Increased leg room and increased width by the operator’s knees compared to 994K.
  • Reduced vibration, low sound levels and automatic temperature controls.
  • Electro-hydraulic speed-sensing steering with force feedback for shift-long comfort.
  • Pressurized cab featuring Next Gen Seat with 9-inch travel, active cooling and heating, adjustable lumbar support, seat cushion tilt adjustment, and air-adjustable bolsters on the seat and backrest.

CONFIDENT & EMPOWERED OPERATORS

  • Low-effort integrated controls that make cycles smoother and faster while reducing fatigue.
  • Large, easy-to-read, color LED displays that provide access to the Electronic Operation & Maintenance Manual.
  • Operator coaching, which helps empower operators to exceed targets by measuring and providing feedback to reinforce proper operating techniques.
  • New Autodig Components that boost efficiency and reduce tire wear by automating critical parts of the digging cycle.
  • Payload Overload Prevention, which inhibits severe payloads from being raised to full truck height.

PRODUCTIVITY

  • Increased rated payload and 6% increase in hydraulic force compared to 994K.
  • Impeller Clutch Torque Converter (ICTC) and Rimpull Control System (RCS), which reduce the potential for wheel slippage without reducing hydraulic efficiency.
  • Superior loading with Cat Performance Series Buckets, which are engineered to dig into piles quickly and load efficiently — with fill factors up to 115%.
  • 3516E engine, which delivers optimum performance through the use of a 16-cylinder, four-stroke design, plus turbochargers and aftercoolers that deliver on-demand performance.
  • Excellent stability thanks to optimized weight distribution, helping operators be more confident and productive.

EFFICIENCY-BOOSTING FEATURES

  • Tire Slip Prevention, which reduces rimpull when there is less downforce on the tire and increases rimpull when there is more downforce on the tire — providing maximum rimpull when you can use it.
  • Tire Set, which automatically applies a lift command at the optimal time to increase traction on the tire, allowing for an increase in usable rimpull.
  • Lift Stall Prevention, which automatically applies the impeller clutch when necessary to prevent hydraulic stall when lifting up through the face — keeping the lift motion continuous, without excessive use of the impeller clutch.
  • Positive Flow Control Hydraulic System, which boosts efficiency with concurrent pump and valve control and increases bucket feel and control to deliver consistent performance.
  • On-demand throttle feature that allows operators to maintain normal operation with the left pedal and implements while the 995 manages the engine speed.

SERVICEABILITY

  • Reduced time spent on regular maintenance procedures thanks to features such as ground-level or platform access to filters; grouped service points; swing-out doors on both sides of the engine compartment; improved access for engine and pump drive service as well as to cooling package; and automatic lubrication system that greases the linkage, hitch, steering and axle trunnion bearings.
  • Service station that provides easy access to functions such as coolant and oil as well as level indicators; Cat battery charging connector; and indicator lights for full fuel tanks.
  • Redesigned pump bay, which offers improved access to transmission components, discharge ports located on the side of pumps, and lines routed directly to screen.
  • Reduced number of steering hoses and tubes; removal of brackets and neutralizers, eliminating the need for neutralizer adjustment; and addition of pilot accumulator, EH valve and pilot filter.
  • Improvements in filters and diagnostics across the machine, with groundline service that includes a steering pilot filter, transmission filters and steering pump discharge screen; pump bay that includes a brake pump filter, implement pilot filter and implement discharge screens; and diagnostic ports that are accessible from the front walk deck and pump bay.

BUCKETS AND GET

  • Approved for higher payloads in low to moderate digging resistance applications; increased payload intended for rehandled material in the ROM pad area or stockpile material, such as coal.
  • Variety of bucket options, including rock buckets for loading limestone or other unprocessed rock; heavy-duty rock buckets for applications like face loading tightly compacted pit materials or handling materials of moderate abrasion and high impact; coal buckets for light density non-abrasive materials; and iron ore buckets for extremely aggressive applications.
  • Performance Series Buckets feature extended floor, dual radius and angled side bars for fast loading; larger bottom box section for increased strength, high fill factors and good material retention; and taller side plate with a level top surface improves operator visibility to the bucket from the cab.
  • Cat Ground Engaging Tools (GET) that feature CapSure™ Retention Technology, which simplifies component replacement with hammerless retention for fast, easy and safe installation.

DURABILITY

  • Highly durable structures, with full box-section rear frame that resists torsional shock and twisting forces to maximize life of mounted components.
  • Frames that utilize castings in key areas to maximize frame durability and optimize efficiency.
  • Rear axle mounting to frame that is optimized to better disperse loads for increased structural integrity.
  • Loads efficiently transmitted by the field-proven solid steel lift arms, with enhanced strength in key pin areas through the use of one-piece castings.
  • Frame, powertrain, engine and components that all built to be rebuilt — using new, remanufactured or rebuilt parts and components — to deliver multiple lives of like-new performance at a fraction-of-new price.

TECHNOLOGY

  • Cat MineStar™ Terrain for loading, which provides real-time feedback on payloads and design plan progress to increases productivity and accuracy, reduce rework, enhance ore control and improve shift-to-shift operator performance.
  • MineStar Object Detection, which combines radar and camera systems to warn operators about light vehicles or stationary hazards within the immediate vicinity of their machines.
  • MineStar Health, which delivers critical event-based machine condition and operating data and includes comprehensive equipment health and asset monitoring capabilities, with a wide range of diagnostic, analytic and reporting tools.
  • Upgraded touchscreen information display that provides intuitive operation and easy navigation and keeps operators informed about machine systems to decrease service time.
  • Cat ProductLink™, which provides remote access to information on machine systems and diagnostic codes; allows you to track utilization, fuel usage and payload summaries; and gives access to machine location, service meter hours and reporting status.

SUSTAINABILITY

  • Designed to be more efficient and use less fuel, which reduces engine emissions and carbon footprint; Tier 4 Final engine reduces NOx and particulate matter.
  • Engine Idle Shutdown, which saves fuel by making it possible to avoid unnecessary idling.
  • Better control of fluids through use of Cat anti-drain filter housings and component ecology drains.
  • Retrofits and upgrades for older machines — to incorporate efficiency improvements and emission reductions, and to keep them in production longer to conserve energy and minimize the need for raw materials
  • Cat Rebuild and Cat Reman programs, which preserve raw materials, conserve energy and reduce emissions.

Standard Equipment:

Optional Equipment:

    Power Train
    • Oil Renewal System (ORS)* (for increased time between oil changes)
    Linkage
    • High lift
    Operator Environment
    • Rubber-mounted, high-impact resistant solar control glass
    • Trainer seat with suspension
    • Joystick lift and tilt function controls
    • Bluetooth®-enabled machine security
    • Sun screen, pull down (front and rear)
    • AM/FM/AUX radio
    • AM/FM/AUX/USB/BT/CD/SAT radio
    Safety
    • Powered ground-access stairs
    • Cat Detect (Rear Object Detection)
    • Wheel chocks
    Cold Weather
    • Cold-weather cooling fan bypass (recommended for temperatures below –29° C [–20° F])
    • Heavy-duty starter (provides an additional electric starter motor and two additional batteries for a total of three starter motors and six batteries) (recommended for temperatures below 0° C [32° F])
    • 240V engine oil and coolant heating elements (recommended in conditions from –18° C to –30° C [0° F to –22° F])
    • Fuel heater (heated by recirculation using engine heat and a heat exchanger) (recommended in conditions from –18° C to –30° C [0° F to –22° F])
    • Heated mirrors (recommended for below-freezing temperatures)
    Machine Control And Guidance
    • Cat Payload with Overload Prevention
    • New Autodig Components:
      – Tire slip prevention

      – Lift stall prevention

      – Tire set

    • Operator coaching
    Fuel Tank
    • 24 hour (5350 L/1414 gal)
    Cooling
    • High ambient package (recommended for site conditions that do not exceed 53° C [127° F])
    Rims And Tires
    • Rims – 1194 mm (47") (47 × 57); 152 mm (6") flange; For use with 58/85-57; 84PR L4 tires
    • Rims – 1194 mm (47") (47 × 57);127 mm (5") flange; For use with 60/80 R57; L5R XMine D2 SR tires
    • Tires – 58/85-57 84PR L4 (require 47" rims)
    Spare Rims
    • 1194 mm (47") 152 mm (44 × 57) (6") flange
    • 1194 mm (47") 127 mm (47 × 57) (5") flange
    Service
    • Product Link satellite
    • Product Link cellular
    • Product Link (dual mode – satellite/cellular)
    • Additional service lights (pump bay, front frame and bumper)
    Sound
    • Sound-suppression package