Caterpillar 775G 0MJS00709

Caterpillar 775G Off-Highway Truck

THE RUNDOWN

ACHIEVE GREATER PRODUCTIVITY
FUEL SAVING STRATEGIES
FUEL SAVING STRATEGIES
BOOST FUEL EFFICIENCY
DESIGNED FOR SAFETY
WORK IN COMFORT
TECHNOLOGY THAT GETS WORK DONE
REDUCED MAINTENANCE COSTS AND OTHER COSTS
APPLICATION VERSATILITY
Engine
Engine ModelCat® C27
Rated Engine Speed2000r/min
Gross Power - SAE J1995:2014825hp
Net Power - SAE J1349:2011783hp
Net Power - ISO 9249791hp
Net Power - 80/1269/EEC791hp
Bore5.4in
Stroke6in
Displacement1648in³
Peak Torque - Speed1300r/min
Net Torque2874ft-lb
Engine Power - ISO 14396813hp
Note (1)Power rating applies at 2,000 rpm when tested under the specified condition for the specified standard.
Note (3)No engine derating required up to 3810 m (12,500 ft) for Tier 2 Equivalent.
Note (2)Ratings based on SAE J1995 standard air conditions of 25° C (77° F) and 100 kPa (29.61 Hg) barometer. Power based on fuel having API gravity of 35 at 16° C (60° F) and an LHV of 42 780 kJ/kg (18,390 BTU/lb) when engine used at 30° C (86° F).
Weights - Approximate
Maximum Gross Vehicle Weight246503lb
Operating Specifications
Nominal Payload Class (100%)71.3ton (US)
Top Speed - Loaded42mile/h
Body Capacity - SAE 2:155.23yd³
Maximum Working Payload (110%)78.3ton (US)
Target Payload (100%)71.3ton (US)
Maximum Allowable Payload (120%)*85.5ton (US)
Note (1)Capacity with Dual Slope body – no liner.
Note (2)* Refer to the Caterpillar 10/10/20 Payload Policy for maximum gross machine weight limitations.
Transmission
Forward - 16.7mile/h
Forward - 29.4mile/h
Forward - 312.7mile/h
Forward - 417mile/h
Forward - 523mile/h
Forward - 631.1mile/h
Forward - 742mile/h
Reverse8.8mile/h
NoteMaximum travel speeds with standard 24.00R35 (E4) tires.
Final Drives
Differential Ratio3.64:1
Planetary Ratio4.80:1
Total Reduction Ratio17.49:1
Brakes
Brake Surface - Front257in²
Brake Surface - Rear9497in²
Brake StandardsISO 3450:2011
Body Hoists
Pump Flow - High Idle118gpm
Relief Valve Setting - Raise2502psi
Relief Valve Setting - Lower500psi
Body Raise Time - High Idle9.5s
Body Lower Time - Float13s
Body Power Down - High Idle13s
Capacity - Dual Slope - 100% Fill Factor
Struck42.7yd³
Note (1)Contact your local Cat dealer for body recommendation.
Heaped (SAE 2:1)*55.5yd³
Note (2)*ISO 6483:1980
Capacity - Flat Floor - 100% Fill Factor
Struck42.2yd³
Note (2)*ISO 6483:1980
Heaped (SAE 2:1)*55.2yd³
Note (1)Contact your local Cat dealer for body recommendation.
Weight Distributions - Approximate
Front Axle - Empty50%
Front Axle - Loaded34%
Rear Axle - Empty50%
Rear Axle - Loaded66%
Suspension
Empty Loaded Cylinder Stroke Front9.2in
Empty Loaded Cylinder Stroke Rear5.8in
Rear Axle - Oscillation8.1°
Service Refill Capacities
Fuel Tank210gal (US)
Cooling System45gal (US)
Differential - Final Drives38gal (US)
Steering Tank9.5gal (US)
Steering System - Including Tank14gal (US)
Torque Converter - Transmission System - HRC18gal (US)
Brake Hoist System85gal (US)
Torque Converter - Transmission System - LRC16gal (US)
Crankcase24gal (US)
Brake/Hoist Hydraulic Tank46.5gal (US)
Tires
Note (2)Caterpillar recommends the customer evaluate all job conditions and consult the tire manufacturer for proper tire selection.
Note (1)Productive capabilities of the 775G truck are such that, under certain job conditions, TKPH (TMPH) capabilities of standard or optional tires could be exceeded and, therefore, limit production.
Standard Tire24.00R35 (E4)
ROPS
ROPS StandardsRollover Protective Structure (ROPS) for cab offered by Caterpillar meets ISO 3471:2008 ROPS criteria.
FOPS StandardsFalling Objects Protective Structure (FOPS) meets ISO 3449:2005 Level II FOPS criteria.
Sound
Sound Standards (1)The operator Equivalent Sound Pressure Level (Leq) is 76 dB(A) when SAE J1166 FEB2008 is used to measure the value for an enclosed cab. This is a work cycle sound exposure level. The cab was properly installed and maintained. The test was conducted with the cab doors and the cab windows closed.
Sound Standards (2)The exterior sound pressure level for the standard machine measured at a distance of 15 m (49 ft) according to the test procedures specified in SAE J88:2008, mid‑gear moving operation is 86 dB(A).
Sound Standards (3)Hearing protection may be needed when operating with an open operator station and cab (when not properly maintained or doors/windows open) for extended periods or in a noisy environment.
Steering
Turning Diameter - Front77.1ft
Steering StandardsISO 5010:2007
Steer Angle31°
Turning Circle - Clearance Diameter85.6ft