C13 ACERT™ Dry Manifold Petroleum Engine
THE RUNDOWN
Custom Packaging
For any petroleum application, trust Caterpillar to meet your project needs with custom factory generator sets and mechanical packages. Cat engines, generators, controls, radiators, and transmissions can be custom designed and matched in collaboration with our local dealers to create unique solutions. Custom packages are globally supported and are covered by a one year warranty after startup.
Custom Packaging
For any petroleum application, trust Caterpillar to meet your project needs with custom factory generator sets and mechanical packages. Cat engines, generators, controls, radiators, and transmissions can be custom designed and matched in collaboration with our local dealers to create unique solutions. Custom packages are globally supported and are covered by a one year warranty after startup.
Full Range of Attachments
Large variety of factory-installed engine attachments reduces packaging time
Testing
Every engine is full-load tested to ensure proper engine performance.
Product Support Offered Through Global Cat Dealer
- More than 2,200 dealer outlets - Cat factory-trained dealer technicians service every aspect of your petroleum engine - Cat parts and labor warranty - Preventive maintenance agreements available for repairbefore-failure options - S•O•SSM program matches your oil and coolant samples against Caterpillar set standards to determine: - Internal engine component condition - Presence of unwanted fluids - Presence of combustion by-products - Site-specific oil change interval
Over 80 Years of Engine Manufacturing Experience
Ownership of these manufacturing processes enables Caterpillar to produce high quality, dependable products.
Over 80 Years of Engine Manufacturing Experience
Ownership of these manufacturing processes enables Caterpillar to produce high quality, dependable products.
Web Site
For all your petroleum power requirements, visit www.cat.com/oilandgas.
General Specifications
| Maximum Rating | 520.0BHP |
| Displacement | 760.0in³ |
| Minimum Rating | 385.0BHP |
| Governor and Protection | Electronic (ADEM™ A3) |
| RPM | 2100.0r/min |
| Aspiration | Turbocharged-Aftercooled |
| Flywheel and Flywheel Housing | SAE 1 |
| Flywheel Teeth | 113 |
| Rotation from Flywheel End | Counterclockwise |
| Stroke | 6.2in |
| Bore | 5.1in |
Emissions
| Emissions | EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA |
Dimensions
| Length | 47.3in |
| Width | 39.9in |
| Height | 46.7in |
| Weight | 1976.0lb |
Capacity for Liquids
| Lube Oil System - Refill | 9.0gal (US) |
| Cooling System | 3.8gal (US) |
Standard Equipment
Air Inlet System
- Turbocharger, mid-mounted
- Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection
Control System
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring system — speed, temperature, pressure
- J1939 Broadcast — diagnostic and engine status
Cooling System
- Thermostats and housing
- Jacket water pump — gear-driven
- Front water pump inlet
Exhaust System
- Exhaust manifold — dry
- Front turbo exhaust
Flywheels and Flywheel Housings
- See Mandatory Options
Fuel System
- Electronic unit injector
- Fuel filter — secondary, mid-mount, (LH 2 micron high performance)
- Fuel transfer pump — front
- Fuel priming pump — LH mid-mount
- Fuel fitting — fuel return connection: straight No. 8, 5/8-18
Lube System
- Crankcase breather
- Oil cooler
- Oil filter — RH
- Oil pan — front sump, 40 L capacity
- Oil filler — LH front
- Oil dipstick — LH front
- Oil pump
- Oil valve sampling — RH rear engine side
Power Take-Offs
- Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width
- Hydraulic pump drive — SAE A, 11-tooth
- 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)
General
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit (connectors, pins, sockets)
- Literature
Mandatory Options
- Flywheel housing or rear PTO
- Throttle position sensor
- Primary filter/water separator
Optional Equipment
Air Compressor
- Air compressors
- Air chambers
- Air compressor governors
Air Inlet System
- Air cleaners
- Precleaners
- Air lines
- Air inlet gasket
Belt-Driven Accessories
- Refrigerant compressor and mounting
Charging System
- Charging alternators
- Alternator mountings
- Alternator guard
- Alternator accessories
Control System
- Connection
Cooling System
- Radiator — installed
- Fan drive f/u/w Caterpillar installed radiator
- Fan drive pulleys f/u/w customer-supplied radiators
- Coolant conditioner
- Water lines — pump inlet
- Fan drive mountings
- Fan height instructions
- Fan adapters for suction fans and blower fans
- Suction fans and blower fans
- Coolant level sensor
- Aftercooler lines
Exhaust System
- Muffler
- Flexible fitting
- Elbows, flange, pipe, clamp
- Straight exhaust adapter
Fuel System
- Fuel lines for fuel filter
- Fuel cooler
- Fuel fitting — fuel return connection
- Flexible fuel lines
Instrumentation
- Gauges and instrument panels
- Voltmeters
- Gauge mounting
- Ammeter
Lube System
- Oil pan
- Oil pan drain
- Oil level gauges
- Oil filter — bypass and remote
- Lubricating oil
- Oil filler
- Fumes disposal
Mounting System
- Front and rear engine supports
- Structural steel base
Power Take-Offs
- Crankshaft pulleys
- Crankshaft pulley — stack-on
- Output flange
- Flywheel stub shaft
- Front stub shaft
- Hydraulic pump drive
- Hydraulic pumps — front and rear
- Enclosed clutch
- Clutch support
Protection System
- Air shutoff
- Air shutoff switch
Starting System
- Starting System
- Starting aids
- Battery sets — 24 Volt, dry
- Battery cable
- Battery rack
Transmission Arrangement
- Transmission cooler
