Cat C18 Auxiliary/Generator Set Engine
THE RUNDOWN
Separate circuit aftercooling system
The primary advantage of the separate circuit aftercooling system (SCAC) is that no sea water circulates through the aftercooler
Emissions
EPA Tier 3 compliant, IMO II and EU IWW compliant
Cooling system
Heat exchanger and Keel cooled options for all ratings
Turbo Configurations
Single turbo configurations for all ratings
Competitive size and weight
Marine Certifications
All major MCS type approvals available from factory
Power Rating
| Power Range | 404 - 803 hp |
| Minimum Rating | 404.0BHP |
| Maximum Rating | 803.0BHP |
Generator Set Specifications
| Frequency | 50 / 60 |
Engine Specifications
| Emissions | IMO II/III, EPA T 3, EU IWW, EU Stage V, China II |
| Aspiration | TA, TTA |
| Bore | 5.7in |
| Displacement | 1106.0in³ |
| Configuration | In-Line 6, 4-Stroke-Cycle Diesel |
| Stroke | 7.2in |
| Rotation from Flywheel End | Counterclockwise |
Dimensions & Weights
| Length | 73.0in |
| Height | 51.2in |
| Dry Weight | 1950.0lb |
| Width | 44.6in |
Standard Equipment
AIR INLET SYSTEM
- Separate circuit after-cooled (SCAC)
- Open Crankcase Ventilation (OCV) system
- Turbocharger, jacket water cooled
- Turbocharger inlet, 152 mm (6 in) OD straight connection
CONTROL SYSTEM
- Programmable low idle
- Electronic diagnostics and fault logging
- Electronic fuel/air ratio control
- Engine Protection Mode for extended ambient conditions - EPA Tier 3 Ratings Only
- 70-pin customer connector
- Three types of throttle inputs (primary/ secondary PWM, 0-5V, 4-20mA)
- Programmable ECM Shutdowns for: High Jacket Water Coolant Temp Low Engine Oil Pressure Engine Overspeed
COOLING SYSTEM
- Separate Circuit After-Cooling (SCAC) for both HEX and Keel cooled engines
- Engine JW and SCAC Shell & Tube Heat Exchangers for HEX cooled engines
- SCAC pump, gear driven, for HEX cooled engines only
- Jacket water pump, gear driven
- Auxiliary water pump, gear driven
- Sea water pump, bronze impeller, gear driven
- SCAC and JW shunt tanks for maintaining proper pump inlet pressures
EXHAUST SYSTEM
- 152 mm (6 in) round flanged outlet
- Water-cooled exhaust manifold & turbocharger
FLYWHEELS & FLYWHEEL HOUSINGS
- Flywheel Housing, SAE No. 0
- Flywheel, 18 inch, 136 teeth
- SAE standard rotation
FUEL SYSTEM
- Front service simplex fuel system
- Fuel transfer pump, gear driven
- Manual fuel priming pump
- Hybrid fuel line design
LUBE SYSTEM
- Front service simplex oil system
- Center sump oil pan: Deep 500 hour oil change interval, Shallow 250 hour oil change interval
- Front and top service oil filler locations
- Front service dipstick
- Oil pump, gear driven
MOUNTING SYSTEM
- Front support - adjustable
POWER TAKE-OFFS
- Poly-V groove for alternator drive
GENERAL
- Front damper guard
- Front service engine
- Common electrical bonding point
- Engine does not ship with zinc components
- NOTE: These engines are for constant speed generator set applications only, and NOT to be used for variable speed applications
Optional Equipment
EXHAUST SYSTEM
- Dry Elbows
- Water-Cooled Elbows
- Flexible Fitting
- Flange
- Muffler
- Muffler Spark Arresting
AIR INLET SYSTEM
- Air Inlet Adapter
CHARGING SYSTEM
- Battery Chargers
- Charging Alternators 24 Volt 70/105 AMP
- Alternator Mounting Group
- Ammeter
CONTROL SYSTEM
- MECP I - Marine Engine Control Panel
- Caterpillar Alarm and Protection
- Load Sharing Attachment
COOLING SYSTEM
- Aux Expansion Flange Kit
FUEL SYSTEM
- Duplex Fuel Filters
- Fuel Cooler
- Fuel Water Separator
- Flexible Fuel Lines
INSTRUMENTATION
- Instrument Panels
- OEM Wiring Harness
- Exhaust Temp Sensor
- Oil Level Sensor
LUBE SYSTEM
- Duplex Oil Filters
- Sump Pump
POWER TAKE-OFFS
- Crankshaft Pulleys
- Front Stub Shaft
- Hydraulic Pump Drive Adapter
- Front Enclosed Clutch
PROTECTION SYSTEM
- Marine Classification Society and SOLAS
STARTING SYSTEM
- Electric Starting Motor - Single 24 Volt
- Air Starting Motor
- Air Start Accessories
- Starting Aids - JW Heaters 120/240V
- Battery Sets - 24 Volt - Dry
MOUNTING SYSTEM
- Front Support
- Rear Support
PACKING
- Engine Protective Cover
- Storage Preservation
- Export Packing