631K Wheel Tractor-Scraper
Quick loading, high travel speeds and the ability to load and dump on the run yield fast cycle times, allowing Cat Wheel Tractor-Scrapers to consistently deliver high productivity at the ...
Tractor Engine
- Flywheel Power - Tractor/Scraper
- 570HP
Scraper Bowl
- Scraper Capacity - Heaped
- 34yd³
Transmission
- Top Speed - Loaded
- 34.7mile/h
Dimensions
- Front of Tractor to Front Axle
- 142.2in
- Axle to Vertical Hitch Pin
- 20in
- Wheel Base
- 346.8in
- Rear Axle - Rear of Machine
- 108in
- Width - Tractor
- 137.8in
- Width - Rear Tire Centers
- 96.9in
- Width - Overall Machine
- 155in
- Width - Outside Rear Tires
- 143.2in
- Width - Inside of Bowl
- 134in
- Length - Overall Machine - Standard
- 597in
- Height - Top of Cab
- 147in
- Height - Scraper Blade Maximum
- 20in
- Height - Overall Shipping
- 153.2in
- Ground Clearance - Tractor
- 26.1in
- Length - Maximum (Push-Pull)
- 655.1in
Travel Speeds - Runout
- Transmission Gear - Second
- 6.2mile/h
- Transmission Gear - Reverse
- 6.2mile/h
- Transmission Gear - Fourth
- 10.5mile/h
- Transmission Gear - First
- 3.4mile/h
- Transmission Gear - Fifth
- 14.1mile/h
- Transmission Gear - Eighth
- 34.7mile/h
- Transmission Gear - Seventh
- 25.7mile/h
- Transmission Gear - Sixth
- 19mile/h
- Transmission Gear - Third
- 7.7mile/h
Safety Criteria Compliance Standards
- Steering System
- ISO 5010:2007
- Seat Belt
- SAE J386:FEB2006
- Rollover Protection Structure (ROPS)
- ISO 3471:2008 for up to 21 282 kg (46,919 lb)
- Reverse Alarm
- ISO 9533:2010
- Falling Object Protective Structure (FOPS)
- ISO 3449:2005 Level II
- Brakes
- ISO 3450:2011
Cab
- ROPS/FOPS
- ROPS/FOPS meet “ISO Standards.”
- Exterior Sound Level
- The exterior sound power level for the standard machine (ISO 6393) is 111.5 dB(A).
Service Refill Capacities
- Transmission System
- 29gal (US)
- Hydraulic System
- 37.5gal (US)
- Fuel Tank
- 231gal (US)
- Diesel Exhaust Fluid (DEF)
- 8gal (US)
- Crankcase - Tractor
- 13.7gal (US)
- Cooling System
- 19.8gal (US)
Engine
- Flywheel Power - Tractor
- 570HP
- Emissions
- Cat C18 engine meets U.S. EPA Tier 4 Final/EU Stage IV emission standards.
- Engine Model - Tractor
- Cat C18
- Rated Engine RPM - Tractor
- 1900r/min
General
- Width - Cut
- 11.5ft
- Top Speed - Loaded
- 34.7mile/h
- Tires - Tractor
- 37.25R35**E3
- Tires - Scraper
- 37.25R35**E3
- Scraper Capacity - Struck
- 24yd³
- Scraper Capacity - Heaped
- 34yd³
- Rated Load
- 37 200 kg (82,200 lb); 37.2 tonnes (41.1 tons)
- Overall Shipping Height
- 12.75ft
- Overall Width
- 12.93ft
- Maximum Depth of Spread
- 21.1in
- Maximum Depth of Cut
- 17.7in
- Fuel Tank Refill Capacity - Scraper
- 231gal (US)
- 180° Curb-to-Curb Turning Width
- 40.12ft
Push-Pull
- Operating Weight - Empty
- 106430lb
- Overall Length - With Bail Down
- 54.59ft
Non Push-Pull
- Operating Weight - Empty
- 102750lb
- Overall Length
- 49.34ft
Implement Cycle Times
- Apron Lower
- 3.8s
- Apron Raise
- 4s
- Bail Lower
- 2.1s
- Bail Raise
- 1.5s
- Bowl Lower
- 3.5s
- Bowl Raise
- 3.5s
- Ejector Extend
- 8.5s
- Ejector Retract
- 8.5s
EFFICIENCY THROUGH TECHNOLOGY
- The Payload Estimator will calculate the payload of the machine in tonnes or tons by measuring the bowl lift cylinder pressures at the beginning of the loaded haul segment. This feature works best when using Sequence Assist. Using Payload Estimator during testing has achieved better than 95% accuracy when compared to actual scale weights. The Payload Estimator feature comes automatically when a machine is ordered with Sequence Assist.
- Load Assist (Optional) is designed to help shorten the learning curve of inexperienced operators to ensure consistency and faster loading of material while reducing effort of the operator. Based on the speed of the machine, Load Assist automatically adjusts the cutting edge height to manage wheel slip and to ensure consistent and efficient loading in bulk earthmoving applications.
- Machine Speed Limit is designed to take the place of top gear selection. If the machine top speed needs to be limited the operator can select the top speed through the display or the top speed can be set in ET. This will allow the machine to find the correct gear that works best for the engine and transmission. Allowing the engine and transmission to select the correct gear to pull the load in most cases resulting in a lower engine load factor and lower fuel burn verses using top gear selection that required the machine to run at engine speeds at or close to high idle.
- Sequence Assist (Optional) uses cylinder position sensors to automate bowl, apron and further implement controls throughout the four core work cycles: Dig, Haul, Unload and Return. When utilized this can reduce up to 14 individual operator commands per cycle. Sequence Assist simplifies control over the implements, reduces joystick usage, automatically controls cushion hitch, transmission hold and ejector.
- Ground Speed Control sets the desired top speed by the operator if job site conditions or segment speed limits require a speed less than full run out. Machine Speed Limit is intended for use when top speed needs to be limited for longer durations and Ground Speed Control is intended for use when the top speed needs to be reduced for shorter segments or intermediate periods of time. The operator can set the desired top speed and the machine will find the correct gear that works best for the engine and transmission.
- Cat Grade Control (Optional) intelligently ensures the machine does not cut below grade in the cut area or over fill in the fill area – avoiding rework and moving unnecessary material.
OPERATOR COMFORT AND CONTROL
- K Series steering system design requires significantly less steering effort. The reduced steering effort will allow for decreased operator fatigue and a more efficient operator resulting in possible higher rates of production late in the work cycle.
- Advanced Cushion Hitch allows the cushion hitch to prevent end stroke by having the ability to predict end stroke events and manage the rate of dampening. Resulting in reduced hitch maintenance and improved operator ride in rough conditions.
- The K Series cab interior improves operator comfort and visibility. The overall interior is 21% larger than the G Series cab.
BUILT-IN SAFETY FEATURES
- In the event of an engine over speed situation, the compression brake or brakes will automatically engage with no operator input. The machine determines the over speed condition based on rate of acceleration and applies compression brakes automatically.
- Differential Lock Engagement Protection- This standard feature allows the machine to prevent the operator from engaging the differential lock when damage could occur.
SAVE ON MAINTENANCE TIME
- The fuel, water and engine oil are relocated at ground level on the right hand side of the machine for easy access.
