992K Wheel Loader
Caterpillar first introduced the 992 in 1968. This large wheel loader has been a global leader ever since, building a reputation as a face loader that's both safe to operate, ...
Engine
- Net Power
- 814HP
- Engine Model
- Cat® C32 ACERT™
- Bore
- 5.7in
- Stroke
- 6.4in
- Displacement
- 1963.5in³
- Torque Rise
- 30%
- Emissions (U.S. EPA Tier 4 Final): Gross Power - ISO 14396
- 884HP
- Emissions (U.S. EPA Tier 4 Final): Rated Speed
- 1750r/min
- Emissions (U.S. EPA Tier 4 Final): Net Power - SAE J1349
- 814HP
- Emissions (U.S. EPA Tier 4 Final): Gross Power - SAE J1995
- 900HP
- Emissions (U.S. EPA Tier 4 Final): Net Power - SAE J1995
- 814HP
- Emissions (U.S. EPA Tier 4 Final): Peak Torque at 1,200 rpm - SAE J1995
- 3514lb/ft
- Emissions (Tier 2 Equivalent): Gross Power - SAE J1995
- 907HP
- Emissions (Tier 2 Equivalent): Net Power - SAE J1349
- 814HP
- Emissions (Tier 2 Equivalent): Gross Power - ISO 14396
- 884HP
- Emissions (Tier 2 Equivalent): Rated Speed
- 1750r/min
- Emissions (Tier 2 Equivalent): Net Power - SAE J1995
- 814HP
- Emissions (Tier 2 Equivalent): Peak Torque at 1,200 rpm - SAE J1995
- 3537lb/ft
- Note (Tier 4 Final) (1)
- These ratings apply at 1,750 rpm when tested under the specified standard conditions.
- Note (Tier 4 Final) (2)
- Rating for net power advertised is based on power available when the engine is equipped with alternator, air cleaner, muffler, and on-demand hydraulic fan drive at maximum fan speed.
- Note (Tier 2 Equivalent) (1)
- These ratings apply at 1,750 rpm when tested under the specified standard conditions.
- Note (Tier 2 Equivalent) (2)
- Rating for net power advertised is based on power available when the engine is equipped with alternator, air cleaner, muffler, and on-demand hydraulic fan drive at maximum fan speed.
Operating Specifications
- Operating Weight
- 220089lb
- Bucket Capacity Range
- 10.7-12.3 m3 (14-16 yd3)
- Operating Weight - Standard
- 220089lb
- Operating Weight - High Lift
- 221847lb
- Rated Payload - Standard Lift (Moderate to High Digging Resistance)
- 24t
- Rated Payload - High Lift (Moderate to High Digging Resistance)
- 21t
Buckets
- Bucket Capacities
- 10.7-12.3 m3 (14-16 yd3)
Transmission
- Transmission Type
- Cat Planetary Power Shift
- Forward - 1
- 4.3mile/h
- Forward - 2
- 7.4mile/h
- Forward - 3
- 12.6mile/h
- Reverse - 1
- 4.7mile/h
- Reverse - 2
- 8.1mile/h
- Reverse - 3
- 13.8mile/h
- Direct Drive - Reverse 2
- 8.8mile/h
- Direct Drive - Reverse 1
- 4.9mile/h
- Direct Drive - Forward 2
- 8mile/h
- Direct Drive - Forward 1
- Disabled
- Direct Drive - Forward 3
- 14.2mile/h
- Direct Drive - Reverse 3
- 15.4mile/h
Axles
- Front
- Fixed
- Rear
- Oscillating
- Oscillation Angle
- 10° ±, 8° ± with Stops
Hydraulic Cycle Times
- Total Hydraulic Cycle Time
- 19.3s
- Raise
- 9.4s
- Dump
- 1.8s
- Rack Back
- 4.4s
- Lower Float Down
- 3.7s
Service Refill Capacities
- Fuel Tank
- 413gal (US)
- Transmission
- 45gal (US)
- Differential - Final Drives - Front
- 95gal (US)
- Cooling Systems
- 77gal (US)
- Hydraulic System - Implement
- 86gal (US)
- Hydraulic System - Steering
- 42gal (US)
- AC Refrigerant
- 6lb
- AC Oil
- 0.071gal (US)
- Differential - Final Drives - Rear
- 91gal (US)
- Engine Crankcase
- 32gal (US)
Hydraulic System - Steering
- Total Steering Angle
- 86°
- Steering System - Pump
- Piston, Variable Displacement
- Steering System - Circuit
- Pilot, Load Sensing
- Steering Cut Off Pressure
- 4500psi
- Maximum Flow at 1,350 rpm
- 95gal/min
- Steering Cycle Times - Low Idle
- 6.4s
- Steering Cycle Times - High Idle
- 4.4s
Dimensions - Standard Lift - Approximate
- Tread Width
- 10.83ft
- Rack Back Angle - Maximum Lift
- 65 degrees
- Clearance at 50° Dump (Tooth Tip)
- 14.7ft
- Ground to Top of ROPS
- 18.63ft
- Ground to Top of Exhaust Stacks
- 17.22ft
- Ground to Top of Hood
- 13.26ft
- Ground to Bumper Clearance
- 3.86ft
- Rear Axle - Centerline to Bumper
- 13.76ft
- Wheel Base
- 19.32ft
- Maximum Overall Length
- 52ft
- Ground to Lower Hitch Clearance
- 2.24ft
- Ground to Center of Axles
- 4.44ft
- Rack Back Angle - Ground Level
- 43.4 degrees
- Rack Back Angle - Carry
- 52.7 degrees
- B-Pin Height - Maximum Lift
- 22.73ft
- Maximum Overall Height - Bucket Raised
- 30.5ft
- Dump Angle at Maximum Lift
- 50 degrees
- Reach - Maximum Lift
- 6.95ft
Dimensions - High Lift - Approximate
- Tread Width
- 10.83ft
- Rack Back Angle - Maximum Lift
- 65 degrees
- Clearance at 45° Dump (Tooth Tip)
- 15.01ft
- Ground to Top of ROPS
- 18.63ft
- Ground to Top of Exhaust Stacks
- 17.22ft
- Ground to Top of Hood
- 13.26ft
- Ground to Bumper Clearance
- 3.86ft
- Rear Axle - Centerline to Bumper
- 13.76ft
- Wheel Base
- 19.32ft
- Maximum Overall Length
- 52.81ft
- Ground to Lower Hitch Clearance
- 2.24ft
- Ground to Center of Axles
- 4.44ft
- Rack Back Angle - Ground Level
- 42.8 degrees
- Rack Back Angle - Carry
- 52.5 degrees
- B-Pin Height - Maximum Lift
- 24.58ft
- Maximum Overall Height - Bucket Raised
- 33.08ft
- Dump Angle at Maximum Lift
- 50 degrees
- Reach - Maximum Lift
- 6.86ft
Sound Performance
- Operator Sound Pressure Level
- The operator sound pressure level is 70 dB(A), measured according to the test procedures and conditions specified in ISO 6396:2008 for the standard machine configuration. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
- Machine Sound Power Level - Standard Machine Configuration
- The machine sound power level is 116 dB(A), measured according to the test procedures and conditions specified in ISO 6395:2008 for the standard machine configuration. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
- Hearing Protection
- Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
- Machine Sound Power Level - Sound Suppressed Machine Configuration
- The machine sound power level is 113 dB(A), measured according to the test procedures and conditions specified in ISO 6395:2008 for the sound suppressed machine configuration. The measurement was conducted at 70 percent of the maximum engine cooling fan s
Hydraulic System - Lift/Tilt
- Tilt Cylinder - Bore
- 10.5in
- Maximum Flow at 1,850 rpm
- 254gal/min
- Lift Cylinder - Stroke
- 45.2in
- Lift Cylinder - Bore
- 11in
- Lift/Tilt System - Circuit
- Positive Flow Control
- Lift/Tilt System - Pump
- Variable Displacement Piston
- Relief Valve Setting - Lift/Tilt
- 4500psi
- Tilt Cylinder - Stroke
- 80.9in
Brakes
- Brakes
- Meet ISO 3450:2011